Browse all practice questions for the PSAD Civil Engineering Licensure Examination (CELE) Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

PSAD Civil Engineering Licensure Examination (CELE) Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • In wastewater collection design, why is slope important?
  • Which expression gives the tensile force T at any point of a catenary cable?
  • Which parameter is the standard design criterion for organic pollution in wastewater treatment?
  • In beam sign conventions, which statement is correct?
  • For displaced concrete neglected and compression steel yields, DRB balance ratio is ρbal_DRB equal to which expression?
  • In concrete technology, why is curing essential for strength development?
  • Which expression correctly gives the magnitude of the resultant force when its components are Rx and Ry?
  • In hydraulics, what does the hydraulic radius represent for a channel?
  • Which set of equations represents the equilibrium conditions in a planar system?
  • DRB Maximum Steel Ratio: ρmax_DRB equals ρmax_SRB plus which term?
  • When steel yields (εs = εy), what is fs?
  • In civil engineering economics, what does the time value of money principle imply for project evaluation?
  • Which expression correctly gives the polar moment of inertia J for a hollow circular shaft (outer diameter D, inner diameter d)?
  • Angle of twist for a shaft is θ = TL / (J G) in radians. Given T = 80 N·m, L = 0.8 m, J = 1.2×10^-5 m^4, and G = 30 GPa, compute θ in radians.
  • Which expression correctly defines the upper bound for ρ in a Tension-Controlled Section?
  • Statement: A fixed-end beam under uniform load has the maximum shear at the supports.
  • Earned Value Management is used for what?
  • The first moment of area Q about the neutral axis is given by which expression?
  • Which expression gives the vertical distance y from the lowest point of a catenary to a point on the cable?
  • For a fixed-ended beam under uniform load w over span L, which expression gives Mmax?
  • In project scheduling, what does 'float' mean in CPM?
  • When displaced concrete is neglected and compression steel yields, ρmax_DRB equals ρmax_SRB plus which term?
  • Which expression gives the length s of a catenary cable?
  • What is the primary purpose of wastewater collection system design?
  • In rectangular beam section analysis, the lever arm a is defined by a = Asfs / (0.85 f'cb). Which expression is correct for a?
  • If Sx is given, bending stress fb is calculated by which expression?
  • Which statement describes the ultimate limit state?
  • What does 'superimposed' load mean in structural analysis?
  • In design codes, why are load combinations used?
  • Which parameter defines slenderness ratio for a member?
  • Which expression correctly defines the horizontal component of a force F making angle θ with the x-axis?
  • For a circular cross-section, which expression correctly gives the maximum bending stress fbmax due to bending moment M?
  • Which formula gives the depth of the neutral axis c based on stress?
  • Which formula is the correct definition of Rn, the coefficient of resisting moment?
  • In hydrology, what is a unit hydrograph used for?
  • Which expression gives the minimum flexural reinforcement Asmin when f'c < 31.36?
  • In RC beam design, what is the primary function of stirrups?
  • In CPM scheduling, Late Finish is defined as the latest time an activity can finish without delaying the project.
  • What is the correct expression for the resisting moment coefficient Rn when ρ is known?
  • For a simply supported beam with a concentrated load P at every 1/3 of the span, which set is correct for Vmax, Mmax, ymax?
  • If the shear force V is integrated with respect to x, which quantity is obtained?
  • If the diameter of a solid shaft is doubled while torque remains the same, by what factor does the maximum shear stress τmax change (τmax ∝ 1/D^3)?
  • Torsional shear stress in a shaft is τ = T ρ / J. If T = 40 N·m, ρ = 0.05 m, and J = 1.5×10^-6 m^4, compute τ in MPa.
  • Allowable Stress F_all is defined by which relation?
  • In structural analysis, what distinguishes indeterminate structures from determinate structures?
  • For a circular cross-section, the maximum bending stress fbmax is given by which expression?
  • What is the standard test to determine the 28-day compressive strength of concrete?
  • In surveying, what is the difference between back sight and fore sight readings?
  • Roller or frictionless surface support provides how many independent reaction components in a planar frame?
  • Moment capacity describes the cross-section's ability to resist bending moments before failure. It depends on which factors?
  • When displaced concrete is neglected, which expression represents DRB balance ratio?
  • Which statement correctly describes the relationship between slenderness ratio and buckling propensity?
  • For normal weight concrete (wc = 2300 kg/m³), which is the Modulus of Elasticity Ec?
  • Which statement best describes the point of inflection in a beam?
  • In concrete technology, which property is most influenced by aggregate grading and shape?
  • For a solid circular shaft with diameter D = 0.05 m under torque T = 50 N·m, τmax = 16 T / (π D^3). Compute τmax in MPa.
  • The DRB balance steel ratio ρbal_DRB equals ρbal_SRB plus which term?
  • If both p and D double while t remains constant, by what factor does sigma_T increase?
  • For a rectangular area with area A located a distance y from the neutral axis, Q = Ay. If A = 40 cm^2 and y = 12 cm, Q equals?
  • In wastewater treatment, what is the main function of the primary clarifier?
  • Which expression represents the steel ratio ρ based on strain?
  • What is the formula for the reinforcement ratio ρ in a rectangular section?
  • If f'c equals 28 MPa, what is β1?
  • Which statement correctly contrasts ASD and LRFD?
  • A shear deformation δs occurs in a member with V = 4,000 N, length L = 0.6 m, cross-sectional area A = 0.003 m^2, and shear modulus G = 25 GPa. Using δs = V L / (A G), determine δs in millimeters.
  • The moment of inertia about an axis located a distance d from the centroidal axis is given by which expression?
  • In structural steel design, which material property governs strength in flexure?
  • In environmental engineering, what is the function of an aeration tank?
  • Radius of gyration r is defined as which of the following?
  • In the steel ratio expressions, what does β1 represent?
  • Average shear stress fv is defined by which formula?
  • In Terzaghi's bearing capacity equation, which term is explicitly associated with the soil unit weight γ?
  • In structural load concepts, what is the difference between dead load and live load?
  • In surveying, what is a closure error and how is it handled?
  • Which equation correctly expresses the relationship between load w, shear V, and moment M with respect to the x-axis?
  • In bending of reinforced concrete sections, what does the neutral axis represent?
  • Allowable Stress Design Principle states that which inequality must hold?
  • Which expression correctly defines ρbal in terms of f′c, f_y, β1, εty, dt and d?
  • How is Manning's roughness coefficient n determined?
  • If a cross-section has I = 200 in^4 and area A = 50 in^2, the radius of gyration r is?
  • The flexural strength of the beam is Mu = φ Rn b d. Which statement best describes this relation?
  • When the steel does not yield (εs < εy), which expression gives fs?
  • Why is a common datum essential in surveying?
  • Which condition is true for a Tension-Controlled Section?
  • In geotechnical bearing capacity, what is a surcharge?
  • Which expression gives the polar moment of inertia J for a hollow circular shaft with outer diameter D and inner diameter d?
  • In Balanced Strain Condition, which relationships hold between steel stress and steel strain?
  • How does c (based on strain) change when εt increases?
  • Which expression gives ρ in terms of Rn?
  • In beam theory, the curvature of the elastic curve is proportional to which quantity?
  • Transition Zone is described by which combination of conditions?
  • In contract administration, what is the purpose of a change order?
  • In project management, what is the purpose of the Critical Path Method (CPM)?
  • What is the primary purpose of the NSCP?
  • For Beams and Frames, the determinacy relation is r = 3n. If there are 4 joints, how many redundants does the frame have?
  • In truss structures, the determinacy condition is m + r = 2j. Which statement correctly reflects this relation?
  • In surveying, what is the method to distribute closure errors in traverse adjustments?
  • Which of the following describes Manning's roughness coefficient n?
  • What does pavement life and reliability denote?
  • For a propped cantilever beam with a uniform distributed load, which set is correct for Vmax, Mmax, ymax?
  • In a Compression-Controlled Section, which statement is true about εt?
  • Fore sight readings are used to measure the position of which point?
  • In water or wastewater treatment, what is biofiltration?
  • Which statement best describes stopping sight distance concept?
  • In Terzaghi's ultimate bearing capacity equation for shallow foundations on cohesive-frictional soils, which term represents the contribution from soil cohesion?
  • According to Wahl's expression, the maximum shear stress Ss for a helical spring involves the parameter m and is given by which form?
  • For a frictionless pin or hinge contacting a rough surface, how many unknowns (components) are present?
  • A plate experiences a shear force V = 5,000 N over an area As = 0.003 m^2. τ = V / A_s. What is τ in MPa?
  • In Transition Zone, which description correctly relates the concrete cover c to dt and cbal?
  • Which formula defines Rn, the coefficient of resisting moment?
  • Area of compression steel As' is calculated by which formula?
  • In contract law, what is liquidated damages?
  • Which expression gives bending stress in terms of bending moment and section modulus?
  • In Transition Zone, which range for ρ is correct relative to ρbal?
  • Using the parallel axis theorem, I_NA = I_CG + Ad^2. If I_CG = 100 in^4, A = 20 in^2, d = 5 in, I_NA equals which value?
  • The approximate formula for the maximum shear stress Ss in a helical spring with load P, mean radius R, and wire diameter d is which of the following?
  • Which statement describes serviceability state?
  • Excess Moment, M2 is defined by which relationship?
  • In design safety, what is the purpose of applying factors of safety?
  • For a hollow circular shaft with outer diameter D = 0.08 m and inner diameter d = 0.04 m under torque T = 60 N·m, τmax = 16 T / [π (D^4 - d^4)]. Compute τmax in MPa.
  • For a short cable (tension only) or a short link, how many unknown reactions are there?
  • For a simply supported beam with a concentrated load at every 1/4 of the span, which set applies for Vmax, Mmax, ymax?
  • In reinforced concrete design, what is the primary role of shear reinforcement (stirrups) in a rectangular beam?
  • In the context of beam bending, how is the point of inflection best defined?
  • Which formula expresses the allowable bearing capacity in terms of ultimate capacity and safety factor?
  • If a channel's cross-sectional area increases while the wetted perimeter remains constant, what happens to the hydraulic radius?
  • Modular Ratio n equals the ratio of the modulus of elasticity of the stronger material to the weaker material.
  • In surveying, what is the purpose of a closed traverse adjustment?
  • How many unknown reactions does a fixed support provide in the plane?
  • Area of Compression Steel of a DRB is given by which formula?
  • A thin-walled cylindrical vessel subjected to internal pressure p = 2 MPa has diameter d = 0.30 m and wall thickness t = 0.02 m. Using σL = p d / (4 t), what is the longitudinal (axial) stress σL?
  • For a simply supported beam with a uniform distributed load w over the span, which set is correct for Vmax, Mmax, ymax?
  • Which term describes the longest path through a project network that dictates the project duration in CPM?
  • For f'c ≥ 28 MPa, β1 is given by which expression?
  • If the ultimate bearing capacity is known and the factor of safety is increased, what happens to the allowable bearing capacity?
  • Shear flow q is defined by which expression?
  • In wastewater treatment, what is the primary purpose of sedimentation tanks?
  • In open-channel hydraulics, the hydraulic radius is defined as A divided by P. If the cross-sectional area A becomes four times larger while the Wetted Perimeter P stays the same, what happens to the hydraulic radius?
  • A collar on a frictionless rod and a frictionless pin in a slot contribute how many unknown reaction components?
  • What is the value of β1 when f'c ≤ 28 MPa?
  • A unit hydrograph is used in hydrology to model what?
  • Bearing stress σb is defined as σb = P / Ab. If a load P = 15,000 N is applied to a bearing area Ab = 0.003 m^2, what is σb in MPa?
  • In environmental engineering, which wastewater effluent parameter is commonly used as a design criterion for organic pollution?
  • In open-channel hydraulics, which parameter represents channel roughness affecting flow velocity?
  • In environmental engineering, what is the primary function of a primary clarifier in wastewater treatment?
  • In transportation engineering, what is the purpose of sight distance in horizontal alignment design?
  • Which factor is most directly affected by proper curing of concrete?
  • In a thin-walled pressure vessel, tangential stress is given by sigma_T = p D / (2 t). What does p denote?
  • Bolt spacing s is given by s = RI / VQ. If the shear term VQ increases, what happens to s?
  • For a simply supported beam with a concentrated load P at midspan, which set of Vmax, Mmax, and ymax is correct?
  • Deformation delta under axial load is given by which formula?
  • A rod of length L = 2.0 m with coefficient of linear expansion α = 1.2×10^-5 /°C is heated by ΔT = 40°C. The thermal deformation is δT = α L ΔT. Compute δT in millimeters.
  • In concrete technology, which property is most influenced by aggregate grading and shape?
  • In Earned Value Management, which term represents the budgeted cost for the scheduled work?
  • Axial strain epsilon is defined as what?
  • If θ = 1.78×10^-4 rad, what is θ in degrees?
  • What is the fundamental objective of bearing capacity analysis for shallow foundations in geotechnical engineering?
  • Which statement correctly compares solid and hollow circular shafts with the same outer diameter D?
  • The deflection δ of a helically coiled spring is given by δ = 64 P R^3 n / (G d^4). Which statement is true about how δ changes with the parameters?
  • General shear stress fv is defined by which formula?
  • For a fixed-ended beam with a uniform distributed load w over span L, which expression gives the maximum shear force Vmax?
  • The stress in the compression steel f's is given by which expression?
  • In materials testing, what does a slump test indicate?
  • For displaced concrete neglected, ρmax_DRB equals ρmax_SRB plus which term?
  • What is the purpose of shear connectors in composite beams?
  • In structural design, what is the purpose of wind load provisions?
  • In the section modulus S = I / c, what does c represent?
  • If τ = 0.8 MPa and γ = 0.0004, compute the modulus of rigidity G using G = τ / γ.
  • Which unit operation in water treatment primarily removes dissolved contaminants via adsorption or ion exchange?
  • In steel design, what is section modulus and why is it important?
  • The modulus of elasticity E relates stress and strain by which expression?
  • Which expression correctly defines the section modulus S in terms of the moment of inertia I and the outer fiber distance c?
  • In a solid circular shaft subjected to torque, where is the maximum shear stress located?
  • If Esteel = 200 GPa and Econcrete = 25 GPa, what is the modular ratio n?
  • If Rn increases while Mu, φ, b, d remain fixed, what happens to ρ?
  • Which expression represents the steel ratio ρ based on stress?
  • Which statement best describes biofiltration?
  • Under axial loading, axial stress sigma is given by which expression?
  • In traffic engineering, what does Level of Service (LOS) measure?
  • Using cbal = (0.003 dt)/(0.003+ εty), what is cbal when dt = 60 and εty = 0.005?
  • In bearing capacity calculations, what is the role of the bearing capacity factor N_q?
  • Which statement best describes Early Start in CPM scheduling?
  • What is the correct expression for the polar moment of inertia J of a solid circular shaft about its axis in terms of its diameter D?
  • In soil classification, what does the plasticity index (PI) indicate, and which soils are typically high in PI?
  • In geotechnical engineering, what is the purpose of soil compaction?
  • Which formula gives the depth of the neutral axis c based on strain?
  • What does the modular ratio n represent?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy